Rectangular Steel Tubing
Rectangular Steel Tubing
video
Rectangular Steel Tubing
Rectangular Steel Tubing2
Rectangular Steel Tubing3
Rectangular Steel Tubing4
1/2
<< /span>
>

Rectangular Steel Tubing

Rectangular Steel Tubing in a full range of sizes and grades, with stock lengths, cut-to-length service, third party inspection and mill test certificates on request. Send your size list and destination port for a quote within 12 hours.

A steel fabricator working on a stadium roof kept failing welding procedure tests on rectangular tubing he had bought on price. The sections looked right and measured right, but the carbon equivalent was above what his procedure allowed, and the welds cracked in the cold. On structural rectangular tubing the section shape is the visible part and the metallurgy is the part that decides whether a job passes, so it is worth specifying both. This page sets out what we supply, what the common grades cover, and what to ask for on a structural order.

How rectangular tubing is made

Rectangular steel tubing covers both square tube and rectangular tube, meaning closed sections with equal or unequal side lengths. It starts as steel strip, which is blanked and levelled, curled into a round tube and welded along the seam. That round tube is then formed into the square or rectangular shape and cut to the required length. Because the section comes from flat strip, the wall is uniform all the way round and the outside faces are flat and parallel, which is what makes the material so easy to fabricate. The final shape is what gives the product its structural value: a closed rectangular profile carries bending and compression loads in both directions at once and resists twisting far better than an open section of the same weight.

Grades and the wall range that suits them

We supply rectangular tubing in yield strength grades 235, 345 and 390. For each grade the wall range runs across two bands, 4 mm to 12 mm and above 12 mm up to 22 mm, so the heavier sections are available without moving to a different specification. Carbon equivalent is controlled at 0.36 or below, which matters on structural work because it governs how the material behaves when it is welded and how it responds if the joint is made in cold weather. Lower strength grades weld most forgivingly and suit general frames, supports and platforms. The higher grades allow a lighter section for the same load, which pays for itself where weight or headroom is tight. If your drawing calls out a carbon equivalent limit, tell us, because it will shape the material we quote rather than being a detail we can add afterwards.

rectangular steel tubing stacked by section size

Why the section shape is worth the money

Structural strength is the headline: a square or rectangular cross section resists bending and compression well in proportion to its weight. Compared with solid steel of the same load capacity, tubing is far lighter, which cuts transport cost and makes erection quicker on site. Fabrication is straightforward, since the sections can be welded or bolted and the flat faces accept brackets without packers. The appearance is orderly enough that exposed work needs no cladding or boxing, and the material cuts, drills and notches with ordinary shop tools. For display and furniture work the same neatly closed shape is chosen for looks rather than strength, which is why the same product turns up in two very different markets.

Fabrication notes

Rectangular tubing welds readily, though on galvanised material the coating must be ground back around the joint and the area ventilated. Where sections are bolted, the flat faces take standard fittings without special preparation. Two things are worth checking on delivery: that the section is true across the faces rather than dished, and that the wall is uniform, since a thin patch shows up as a weld that blows through. We measure both before each bundle leaves. If a joint is to be made in cold conditions, mention it, and we will flag whether the grade you have chosen is comfortable with that.

Questions buyers ask us

Square or rectangular? Square sections suit columns and members loaded in two directions. Rectangular is more efficient where the load runs mainly one way, such as a beam or a purlin. Send the span and the load and we will suggest a section.

Can I get the same outside size in a heavier wall? Yes, that is a common way to raise capacity without reworking connections.

Do you issue mill certificates? Yes, with every shipment, and the heat number is tagged on each bundle.

Can the tube be cut and notched? Cutting to length is standard. Notching is available where the quantity justifies setting up for it.

rectangular steel tubing end detail and wall section

Get a quote

Send the outside dimensions, wall thickness, length, grade, carbon equivalent limit if the drawing names one, quantity and destination port. A sales engineer replies within 12 hours with per-tonne pricing, available stock and the earliest loading date we can commit to. If the section you have specified is not the most efficient choice for the span and load, we will say so, and we will not substitute material without telling you.

Hot Tags: rectangular steel tubing, rectangular steel tubing price, rectangular steel tubing supplier, buy rectangular steel tubing, rectangular steel tubing specification, square tube exporter, Mild Steel Tube, Square Tube, Square Metal Tubing, 2 Inch Square Tubing, 1 2mm Thickness Square Steel Tube, Rectangular Steel Tubing

Send Inquiry

(0/10)

clearall