Square Galvanized Steel Tube
Square Galvanized Steel Tube
video
Square Galvanized Steel Tube
Square Galvanized Steel Tube2
Square Galvanized Steel Tube3
Square Galvanized Steel Tube4
Square Galvanized Steel Tube5
1/2
<< /span>
>

Square Galvanized Steel Tube

Square Galvanized Steel Tube in a full range of sizes and grades, with stock lengths, cut-to-length service, third party inspection and mill test certificates on request. Send your size list and destination port for a quote within 12 hours.

The only reliable moment to weigh a zinc coating is while the bundle is still on the truck. Once galvanised tube is stacked, bolted and covered in site dust, nobody can tell a properly coated section from a lightly coated one, and an argument about whether the order met specification becomes a matter of opinion rather than measurement. On tube that will stand outdoors for years, coating weight is the specification. Here is what we supply and what belongs on the enquiry.

Coating weight is the specification

Hot dip galvanising begins with the tube being cleaned through a sequence of caustic and acid baths that strip oil, scale and mill dirt from the surface. It is then fluxed and immersed in a bath of molten zinc, where the zinc reacts with the steel and forms a coating bonded into the surface rather than laid over it. The tube is drained and cooled, leaving a dull grey finish with a slight spangle. The coating protects twice over: as a barrier that keeps moisture off the steel, and as a sacrificial layer that corrodes in preference to the steel wherever the surface is broken. A section that is cut on site, dragged across a truck bed or drilled for a bracket keeps working; a painted one has to be touched up. That behaviour scales with how much zinc sits on the surface, so name the coating weight or class your specification applies.

What we hold

Square, rectangular, round and oval sections are all supplied, with wall thickness quoted from 0.2 mm through to 25 mm depending on the section and the duty. Standard lengths are 6 m and 12 m, and cut lengths are prepared to your list before packing. Thin wall goes into frames, panels and light fencing where weight is the enemy. The heavy end is for members that carry real load or absorb impact. If the wall is not something you have calculated, send the span and the loading and we will work through the section with you rather than quoting the lightest option on the shelf.

hot dipped galvanized square steel tube sorted by section size

Grades

Base material comes from Q195, Q235, Q235B, Q345, Q345B, St37, St42 and St37-2. Lower carbon grades bend and weld without fuss and cover most fabricated frames. Q345 and Q345B raise the yield for loaded members, which lets a lighter section do the same work. St37-2 and its neighbours still appear on European drawings, and specifying by the old name remains common enough that we hold material to suit. Tube is supplied against ASTM, API, JIS and ISO 9001 as the order requires, with mill certificates issued with the shipment. Tell us which standard the inspector will read, because naming an equivalent rather than the required grade is the quickest route to a rejected delivery.

Fabrication on site

Galvanised section fabricates like bare steel apart from two points. Every cut end and drilled hole exposes uncoated steel, so on exposed work those faces want a zinc rich repair coating, which can travel with the order. Welding releases zinc fume, so the coating should be ground back roughly 50 mm either side of a joint and the area ventilated. Bolt together frames avoid both issues, which is why much agricultural and fencing work is assembled rather than welded. If the tube will be threaded or coupled, say so when you enquire and the ends will be prepared accordingly.

Where it goes

Building structure takes the largest share, from portal frames and mezzanine floors to stair stringers and handrail. Agricultural irrigation is close behind, with tube running outdoors through heat, frost and spray for years at a time. Fluid transport, fencing, greenhouse frames, sign structures and trailer chassis all belong in galvanised section. The common thread is exposure. Where the finished piece will stand in weather, in a wash down bay or in damp ground, the galvanised option costs less over the life of the installation than bare steel and a repaint every few years.

galvanized square tube end detail showing coating across the wall

Common questions

What coating weight do you supply? Give us the zinc weight or class your specification names and we will quote against it. Where nothing is stated we will ask, because assuming is how mismatched batches end up on the same site.

Will sections from different orders match in colour? Sections dipped in the same run match most closely. If appearance matters, place the full quantity at once and note it on the enquiry.

Can we weld it in the workshop? Yes, with the coating ground back either side of the joint and extraction in place. We can send a length of bare tube for procedure trials.

Do you cut to length? Yes. A cut list saves a handling operation on site and cuts waste in your yard.

How to price it

Send the section size, wall thickness, length, grade, coating requirement, quantity and destination port. You will have per-tonne pricing within 12 hours, together with what is physically in stock and the earliest vessel we can honestly make. Where the coating you have specified is unusual, or the lead time runs past the date your schedule allows, we will say so while you still have room to change the order.

Hot Tags: square galvanized steel tube, square galvanized steel tube price, square galvanized steel tube supplier, buy square galvanized steel tube, square galvanized steel tube specification, galvanized steel pipe exporter, Galvanized Steel Tube, Hot Dipped Galvanized Steel Pipe, Galvanized Steel Pipe, Square Galvanized Steel Tube, 1 Inch Gi Square Pipe, Galvanized Iron Square Pipe

Send Inquiry

(0/10)

clearall