
Square Hollow Section
Square Hollow Section in a full range of sizes and grades, with stock lengths, cut-to-length service, third party inspection and mill test certificates on request. Send your size list and destination port for a quote within 12 hours.
A mezzanine floor in a Nairobi warehouse had been designed around square hollow sections at 6 m spans. When the sections arrived from a cheaper source the wall was there but the corner radii were inconsistent, and the welder could not close the joints without packing them. A hollow section is only useful if the outside faces are true and the wall is where the drawing says it is, because everything downstream, cutting, notching, welding and bolting, is built on that assumption. This page covers what a square hollow section is, what we supply and what to check.
What a square hollow section is and why it is used
A square hollow section, usually shortened to SHS, is a closed square profile formed from steel strip, welded along one side, and then galvanised or left bare according to the job. Closed sections carry load in two directions at once and resist twisting far better than an open profile of the same weight, which is why they turn up wherever a structure needs to be stiff and light rather than merely strong. The flat faces take bolts and brackets without special preparation, the closed body traps no water on the inside, and the appearance is clean enough that exposed work needs no cladding. The hollow body is also part of the reason galvanised SHS lasts as long as it does, since the zinc reaches the inside surface during dipping and protects it there too.
The range we hold
Section sizes run from 15 mm up to 400 mm, wall thickness from 0.6 mm to 20 mm, and lengths from 1 m to 12 m. Light wall sections in the smaller sizes suit frames, gates, shelving and display work where weight matters more than stiffness. Medium wall square sections are the workhorse for structural frames, supports and platforms. The heavy end of the range goes into columns, crane and machine bases and any member carrying serious compressive load. Standard lengths are mill lengths and we cut to your list where the job needs it, so the pieces arrive sized rather than being trimmed twice.

Grades and standards
We supply SHS in Q195, Q215, Q235, Q345 and S235JR. Q195 and Q215 are low carbon material that bends and welds readily, and they are the usual choice for fabricated frames and general structural work. Q235 is the common middle ground that most commercial jobs are drawn in. Q345 brings a higher yield for members carrying real load, and S235JR answers European drawings by their own designation rather than by an equivalent. Material is supplied against JIS and ISO 9001 certification as the order requires, and mill certificates are issued with the shipment. If your drawing names a standard, tell us which one the inspector will read, because a near equivalent grade is not the same thing in a rejection report.
Fabrication notes
Square hollow sections cut cleanly with a saw or abrasive disc, and the closed profile makes notching straightforward when the ends need to meet at an angle. Welding is normal practice, with the caveat that galvanised material requires the coating ground back around the joint and adequate ventilation. Where sections are bolted, the flat faces accept standard brackets without packers. Two details are worth checking on delivery: that the section is square across the corners rather than dished, and that the wall is uniform, since a thin patch will show up as a weld that blows through. We measure both before the bundle leaves the yard. Galvanised SHS can be expected to serve for a very long time outdoors, with actual life governed by how much zinc is on the surface and how corrosive the site is.
Questions buyers ask us
Square or rectangular, which should I use? Square sections suit columns and members loaded in two directions. Rectangular is more efficient when the load runs mainly one way, such as a beam. Send the span and load and we will suggest a section.
Can you supply the same section in a heavier wall for the same outside size? Yes, that is a common way to increase capacity without reworking connections.
Do you issue mill certificates? Yes, with every shipment, and the heat number is tagged on each bundle for traceability.
Can sections be cut to length and notched? Cutting to length is standard. Notching is available on request where the quantity justifies setting up for it.

Get a quote
Send the outside dimensions, wall thickness, length, grade, coating requirement, quantity and destination port. A sales engineer replies within 12 hours with per-tonne pricing, what is in stock today and the earliest loading date we can commit to. If the section you have specified is not the most efficient choice for the span and load, we will tell you, and we will not substitute a section without saying so.
Hot Tags: square hollow section, square hollow section price, square hollow section supplier, buy square hollow section, square hollow section specification, galvanized steel pipe exporter, Galvanized Iron Square Pipe, Galvanized Steel Pipe, 1 Inch Gi Square Pipe, Square Hollow Section, Hot Dipped Galvanized Steel Pipe, Galvanized Steel Tube
Send Inquiry











