
Galvanized Steel Tube
Galvanized Steel Tube in a full range of sizes and grades, with stock lengths, cut-to-length service, third party inspection and mill test certificates on request. Send your size list and destination port for a quote within 12 hours.
An irrigation contractor in Kenya came back to us with a length of tube that had rusted from the inside out in under two years. The tube had been dipped, but the bore had never been cleaned before dipping, so the zinc never bonded and the water did the rest. Galvanised steel tube is not complicated, but the quality of it depends entirely on preparation, and preparation is the part that is invisible on a delivery note. This page covers how the tube is made, what we supply, and what is worth checking before you accept a shipment.
How galvanising is done properly
The tube is first cleaned in a sequence of baths that strip oil, mill scale and dirt from both the outside and the bore. It is then fluxed and dipped into a bath of molten zinc, where the zinc reacts with the steel to form a coating bonded into the surface rather than applied over it. The tube is drained and cooled, and the result is a dull grey finish that protects the steel in two ways: it seals the surface against moisture and chemicals, and it sacrifices itself at any break so that the surrounding steel stays sound. The cleaning step is what makes the difference between a coating that lasts and one that flakes off in sheets. We specify bore cleaning on tube destined for water service for exactly this reason.
Grades, sizes and processing
We supply galvanised steel tube in A36, Q195, Q215, Q235, Q345, 10# and 20# grades, with wall thickness quoted from 0.2 mm to 30 mm or to your own requirement. Welding and cutting are both available as part of the order, so tube arrives in the lengths and with the end preparation the job needs rather than being reworked on site. The low carbon grades are the ones that bend and weld easily and they cover most structural and fluid work. A36 answers American drawings and 10# and 20# are the grades that Chinese and some Asian specifications call up for fluid and general purpose tube. If your drawing names a grade, send it over, because the carbon content decides how the tube behaves under the welder as much as how it performs in service.

Where it goes
Water and fluid work is the biggest single use, covering plumbing, water supply lines and irrigation systems where the tube will be wet for most of its life. The same material is used for structural frames, greenhouse and shed framing, handrails, gates and general fabrication, where the priority is simply a tube that will not need painting every couple of years. Because the coating is bonded rather than applied, galvanised tube also tolerates being installed in ground or in a damp wall without the rapid breakdown that bare steel shows in the same position.
What to check on delivery
Look at a cut end. The coating should be continuous across the wall and slightly thickened at the edge, and there should be no bare steel showing through in patches. Check the bore on a sample by holding it to the light; a properly prepared tube shows the same grey coating inside. Wall thickness and outside diameter should match the mill certificate, and we gauge a sample from each bundle before dispatch. Lengths are checked against the cut list, and every bundle is tagged with its heat number so a receiving inspector can trace the material without a phone call.
Questions buyers ask us
Is the bore galvanised as well? Yes, where the tube is cleaned properly before dipping. That is standard on our water service tube, and we can confirm it on the certificate.
Can you weld the tube for me? Welding and cutting are offered as part of the order. Send the fabrication details and we will quote it with the tube.
Will it be suitable for drinking water? Tell us the standard the project applies and we will confirm which finish is acceptable before quoting.
How should cut ends be treated on site? With a zinc rich repair coating. We can supply it with the order so the pipe stays protected after fabrication.

Get a quote
Send the outside diameter, wall thickness, length, grade, quantity and destination port. We reply within 12 hours with per-tonne pricing, what is in stock today and a realistic loading date. If the application needs the bore coated or the ends prepared in a particular way, say so on the enquiry rather than after the order is confirmed.
Hot Tags: galvanized steel tube, galvanized steel tube price, galvanized steel tube supplier, buy galvanized steel tube, galvanized steel tube specification, galvanized steel pipe exporter, Galvanized Iron Square Pipe, Galvanized Steel Tube, Galvanized Steel Pipe, Hot Dipped Galvanized Steel Pipe, Square Hollow Section, 1 Inch Gi Square Pipe
Send Inquiry











