Hot Dipped Galvanized Steel Pipe
Hot Dipped Galvanized Steel Pipe
video
Hot Dipped Galvanized Steel Pipe
hot dipped galvanized steel pipe2
hot dipped galvanized steel pipe3
hot dipped galvanized steel pipe4
hot dipped galvanized steel pipe5
1/2
<< /span>
>

Hot Dipped Galvanized Steel Pipe

Hot Dipped Galvanized Steel Pipe in a full range of sizes and grades, with stock lengths, cut-to-length service, third party inspection and mill test certificates on request. Send your size list and destination port for a quote within 12 hours.

A chemical plant in Nigeria replaced a run of pipe three times in six years before switching suppliers. The pipe was described as galvanised on both occasions, but one lot was electroplated and the other hot dipped, and the difference showed up in the thickness of the zinc rather than on any label. Hot dipped galvanised steel pipe carries a substantially heavier coating than the electroplated alternative, and in a wet, salty or chemical environment that coating thickness is the entire service life of the pipe. Here is how the two processes differ and when the heavier one is worth paying for.

Hot dip and electroplated are not the same product

Hot dip galvanising dips the finished pipe into a bath of molten zinc, where the zinc reacts with the steel surface and forms a coating that is bonded into the metal rather than sitting on top of it. Electroplating, often called cold galvanising in the trade, passes the pipe through an electrolytic bath and deposits a much thinner layer of zinc on the surface. The hot dipped coating is thicker, more uniform, and adheres far more strongly, which is why it lasts longer in service. The electroplated route costs less, and it has its place on indoor work and on components where a smooth decorative finish matters more than long term exposure resistance. What it should not be used for is a marine site, a chemical plant or an outdoor installation where nobody intends to repaint anything.

hot dipped galvanized steel pipe stacked for export

What the zinc layer is doing

The coating keeps oxygen and moisture away from the steel, which stops the oxidation that would otherwise turn the pipe into rust. It also does something a paint film cannot. When the layer is damaged, the zinc around the break corrodes in preference to the steel underneath, so a scratched pipe keeps working instead of failing at the scratch. That is the practical reason galvanised pipe survives being dragged across a loading dock, and why the same treatment on a handrail or a fence post lasts for years without attention. The other thing worth knowing is that the coating has a mechanical role as well as a chemical one: a properly bonded zinc layer adds resistance to impact and abrasion, so a galvanised pipe takes knocks on site that would dent through the coating of a thinly plated one.

Where hot dipped pipe is specified

Coastal and marine installations are the classic case, since salt air attacks bare steel quickly and consistently. Chemical plants, water treatment works, agricultural buildings, wash down areas and any outdoor structure expected to stand for decades all belong in the same group. The pipe also handles harsh weather without special treatment, standing up to strong ultraviolet exposure and rain erosion that would break down a paint system within a few seasons. In each of these settings the reasoning is the same: the owner wants to install the pipe once and then forget about it, and the heavier coating is what buys that.

Cutting, threading and handling

Galvanised pipe cuts and threads like ordinary steel pipe, with the caveat that every cut end and threaded joint exposes bare steel. On exposed work those points should be dressed with a zinc rich repair coating, which we can supply with the order. Welding requires the coating to be ground back either side of the joint and the area ventilated, since zinc fume is not something to breathe. Where pipe will be in contact with a dissimilar metal, an insulating layer at the joint avoids galvanic trouble later. Tell us at the enquiry stage if pipe is to be threaded, grooved or welded, so the ends can be prepared the way the job needs.

Questions buyers ask us

How do I tell hot dipped from electroplated? The hot dipped coating is visibly thicker and has a duller, slightly spangled surface. If in doubt, ask for the coating weight on the mill certificate rather than judging by appearance.

What coating weight can you supply? Tell us the weight or class your specification names and we will quote against it. If nothing is stated, we will ask rather than guess.

Can I paint over it? Yes, once the surface has weathered or been prepared. A galvanised pipe that is painted as well lasts longer still in aggressive environments.

Do you supply cut lengths and threads? Yes, send the cut list and the joint details and we will prepare before packing.

galvanized pipe coating inspection before shipment

Get a quote

Send the outside diameter, wall thickness, length, quantity, coating requirement and destination port. We come back within 12 hours with per-tonne pricing, current stock and the earliest loading date we can honestly commit to. If your environment will beat an electroplated finish, we will tell you plainly, because re-shipping pipe to a coastal site is expensive for both of us.

Hot Tags: hot dipped galvanized steel pipe, hot dipped galvanized steel pipe price, hot dipped galvanized steel pipe supplier, buy hot dipped galvanized steel pipe, hot dipped galvanized steel pipe specification, galvanized steel pipe exporter, 1 Inch Gi Square Pipe, Galvanized Steel Pipe, Square Hollow Section, Galvanized Iron Square Pipe, Square Galvanized Steel Tube, Galvanized Steel Tube

Send Inquiry

(0/10)

clearall