Galvanized Steel Pipe For Gas Line (EN 10255, Threaded, Hot Dip After Welding)

Galvanized Steel Pipe For Gas Line (EN 10255, Threaded, Hot Dip After Welding)

Hot dip galvanized steel pipe for gas distribution, EN 10255 medium and heavy class, ASTM A53 Gr.B, DN15-DN100, ISO 7-1 tapered threads gauged on every length, zinc coating inside and out after welding, hydrostatic and eddy current tested, EN 10204 3.1 MTC per order.

Gas line pipe is judged on two things: the thread and the bore. Everything else on a galvanized tube can carry a small fault without anyone noticing. A gas joint cannot. We roll EN 10255 medium and heavy tube, dip it in our own zinc kettle after the weld is made, and cut ISO 7-1 tapered threads that are gauged on every single length before it leaves the yard. A pipe that threads hard, or runs loose after two turns, costs a fitter a morning on site. A joint that weeps at commissioning costs far more than the pipe ever did.

The coating is applied after welding, not before. That detail decides whether the weld zone is protected. Pre-galvanized strip has bare, heat-affected seams once the tube is formed and welded, and on a gas service that seam sits wet for years. Our line welds first, then galvanizes, so the inside face, the weld bead and the outside all come out of the same kettle with the same zinc. Mean coating weight runs 450 to 550 g/m² depending on bore, applied to EN 10240.

Specifications

ItemRange
StandardsEN 10255 (formerly BS 1387) medium & heavy; ASTM A53 Gr.B; ISO 65
Nominal boreDN15 – DN100 (1/2" – 4")
Outside diameter21.3 – 114.3 mm
Wall thicknessMedium class 2.0 – 3.6 mm; heavy class 2.6 – 4.5 mm
Steel gradeS195T / Gr.B equivalent, typical yield 195 MPa min
Zinc coatingHot dip after welding, inside and outside, EN 10240, mean 450 – 550 g/m²
ThreadsISO 7-1 tapered (R series), ring and plug gauged on 100% of lengths
Lengths5.8 / 6 m random, fixed length by agreement
TestingHydrostatic, eddy current on every length, flattening test per batch
EndsThreaded with socket and plastic cap, or plain for welding
DocumentsEN 10204 3.1 MTC per order, zinc weight certificate on request

Threads, and why we gauge every length

A tapered thread per ISO 7-1 seals on the flanks, and it only seals if the crest and root sit inside gauge tolerance along the whole thread length. We cut threads on the same line that sizes the tube, then pass each length through a ring and plug gauge. The gauge decision is recorded per bundle. We also keep the thread protectors on through loading, because a dented first thread at the port is the most common complaint in this trade and the cheapest one to prevent.

galvanized steel pipe for gas line threaded ends

Inside coating matters as much as outside

Gas distribution pipe carries air, moisture and occasional condensate, and the inside face is the one nobody inspects. After dipping, we drain and blow each tube so the bore has no zinc pooling or runs that could catch debris downstream. If your network runs below grade, the same tube works with a wrapped or PE-coated outside; tell us the burial class and we quote the extra coating with it, rather than leaving you to source it in two places.

hot dip galvanized gas pipe bundles in yard

Packing and shipment

Standard bundles run 500 to 1,000 kg in hexagonal form, steel strapped, threaded ends capped. A 20 ft container takes roughly 24 to 27 tonnes of DN25 medium depending on the mix of lengths. Bundle tags carry size, class, standard and gauge batch number, so your storekeeper can trace a bundle back to its MTC without opening the strapping.

galvanized gas pipe hexagonal bundles packed for export

Request a Quote

Send the nominal bore, class (medium or heavy), thread requirement and destination port. If your project follows EN 12007-2 for the network side, say so, and we will match the pipe documents to what your inspector expects to see. A sales engineer replies within 12 hours with price, coating weight confirmation and the first shipping window.

Send Inquiry

(0/10)

clearall