16 Gauge Hot Rolled Steel Sheet (1.5 mm, Q235B / S235JR / A36)
16 Gauge Hot Rolled Steel Sheet (1.5 mm, Q235B / S235JR / A36)
video
16 Gauge Hot Rolled Steel Sheet (1.5 mm, Q235B / S235JR / A36)
16 gauge hot rolled steel sheet2
16 gauge hot rolled steel sheet3
16 gauge hot rolled steel sheet4
1/2
<< /span>
>

16 Gauge Hot Rolled Steel Sheet (1.5 mm, Q235B / S235JR / A36)

16 gauge hot rolled steel sheet, 1.5 mm, width 1000-1500 mm, length up to 6000 mm. Q235B, S235JR, SS400, A36. Black mill finish or pickled and oiled. Thickness measured at three points per sheet before the certificate is printed.

Sixteen gauge is 1.52 mm on a US gauge table and 1.5 mm on a metric drawing, and in practice the same sheet answers to both. What actually separates a good 16 gauge order from a bad one is the tolerance underneath the number and the surface condition it arrives in. A 1.5 quoted at 1.38 still welds, but the bend radius comes out wrong and the press brake tonnage was set for a heavier strip.

We roll this gauge on our own line, in Q235B, S235JR, SS400 and A36, and cut it on a 6 metre shear. Before a certificate is printed, thickness is measured with a micrometer at three points across the strip, one third in from each edge and one in the centre, because a coil that runs heavy in the middle passes a single spot check and still causes trouble on a wide part. Those readings go on the MTC.

Specifications

ItemDetail
Gauge / thickness16 ga = 1.52 mm (US) / 1.5 mm (metric)
Thickness tolerance±0.10 mm, minus side held at 0.05 mm
Width1000 / 1219 / 1500 mm, slit widths to order
Length2440 / 3000 / 6000 mm, or cut to your blank size
GradesQ235B, S235JR, SS400, A36, S275JR
Yield / tensile≥ 235 MPa / 370-510 MPa
Elongation≥ 21%
SurfaceBlack mill finish, or pickled and oiled
Flatness≤ 8 mm per metre after levelling
StandardsEN 10051, EN 10025-2, ASTM A1011, JIS G 3101
CertificateEN 10204 3.1, chemistry and measured thickness
Bundle2-3 t, steel strapped, oiled paper interleaved

Black or pickled and oiled

Black sheet still carries mill scale. That is fine for parts that get welded, blasted or galvanized afterwards, because the next process removes the surface anyway. It is not fine for direct painting, because paint bonds to the scale and the scale eventually lets go of the steel.

Pickled and oiled sheet goes through our acid line to strip the oxide, then gets a light oil film to hold back flash rust. It costs a little more per tonne and arrives ready for pretreatment or powder coat. We quote both finishes side by side, and if the coil is going straight to a paint line we will say which one to buy rather than let the cheaper one go out.

16 gauge hot rolled steel sheets stacked in warehouse

What it gets used for

Brackets, base plates, trailer cross members, machine guards, tank saddles, agricultural frames. At 1.5 mm the sheet forms on a medium brake and still holds a structural weld. Most of what we ship in this gauge goes to fabricators who cut and weld in-house, so cut-to-length blanks are a large part of our business here: tell us the part size and we will quote blanks banded in packs instead of full sheets with offcuts left over. The common widths, 1219 and 1500, roll almost every week on our schedule, so standard sizes move quickly; odd widths wait for the next rolling slot.

Packing and loading

Cut sheets are levelled, stacked flat under weight, interleaved with oiled paper and steel strapped on a wooden skid. Each bundle tag carries heat number, size and weight. A 20 ft container takes about 25 tonnes at 1500 x 3000, roughly 140 sheets, and we can arrange shipment from Tianjin or any port you nominate.

hot rolled steel sheet bundles strapped for container loading

Enquiries

Send the thickness or gauge, sheet or blank size, grade, quantity and finish. You get price, a sample MTC and the next rolling date within 12 hours. If you want to test the surface before committing to a container, sample sheets go out by courier.

Send Inquiry

(0/10)

clearall