Z60 Galvanized Steel Coil (60 g/m2, Indoor & Duct Grade)
Z60 Galvanized Steel Coil (60 g/m2, Indoor & Duct Grade)
video
Z60 Galvanized Steel Coil (60 g/m2, Indoor & Duct Grade)
Z60 Galvanized Steel Coil (60 g/m2, Indoor & Duct Grade)2
Z60 Galvanized Steel Coil (60 g/m2, Indoor & Duct Grade)3
Z60 Galvanized Steel Coil (60 g/m2, Indoor & Duct Grade)4
Z60 Galvanized Steel Coil (60 g/m2, Indoor & Duct Grade)5
1/2
<< /span>
>

Z60 Galvanized Steel Coil (60 g/m2, Indoor & Duct Grade)

Z60 hot dip galvanized steel coil, 60 g/m2 zinc coating, 0.3-2.0 mm thick, 600-1250 mm wide. DX51D+Z / SGCC, regular or zero spangle, chromate passivated and oiled. Coating mass checked on both faces twice per shift. 3-8 t coils, 508/610 mm ID.

Z60 means 60 grams of zinc per square metre in total, roughly 30 g on each face, run onto cold rolled substrate on our own hot dip line. It is the coating weight for dry indoor work: HVAC duct, cable tray, ceiling grid, roller shutter guides, interior partition framing. Zinc below that weight is thin enough to worry about; zinc above it is metal that will never corrode away inside a building.

Coating mass is the number everything else hangs off. We check it on both faces twice a shift and the figures go on the certificate next to the chemistry, because a Z60 order that quietly ships at Z40 looks fine on the coil and fails in service two years later. The only defence is measurement, so we measure. Roughly two thirds of our Z60 ends up in duct and tray; the rest goes to shutter makers and ceiling grid roll formers, all of it slit to width here before it leaves.

Specifications

ItemDetail
Coating weightZ60 = 60 g/m² total, approx. 30 g per face
Thickness0.3 – 2.0 mm
Width600 – 1250 mm, slit on our line
SubstrateDX51D+Z, SGCC, CS-B
SpangleRegular spangle or zero spangle
Surface treatmentChromate passivated, oiled
Coil ID / weight508 or 610 mm / 3-8 t, split coils on request
Yield strength270 – 500 MPa by grade
Elongation≥ 18%
Bend performance0T-1T at coating weights up to Z90
StandardsEN 10346, JIS G 3302, ASTM A653, GB/T 2518
CertificateEN 10204 3.1, coating mass report included
Other weightsZ40, Z90, Z120, Z180, Z275 off the same line

Outdoor work needs a heavier coating

Rain, condensation and salt eat thin zinc fast. Roofing, outdoor cladding and anything near the coast should not be quoted at Z60, and we do not quote it there. Outdoor work starts at Z180, coastal sites move to Z275 or a prepainted finish. When an enquiry says outdoor, we price the heavier coating and write the reason on the quotation, even if the buyer asked for the cheap one first.

Spangle

Regular spangle shows the familiar crystalline zinc pattern. Zero spangle is smoother and the better base under paint. The zinc weight is the same either way, so for duct and tray the choice comes down to appearance, and for anything that will be painted afterwards, zero spangle is the one to order. Passivation is chromate unless you ask for a chromium-free treatment, which some food and cleanroom work specifies.

Z60 galvanized steel coils in our coil yard

Slitting and coil handling

We slit to width in house, burr on one side only, and inspect the first and last metre of each slit coil so a wavy edge does not turn up at the tail end where it stops your line. Coil ID is 508 or 610 mm to suit your mandrel, and coil weight is split to the capacity of your uncoiler. Slit coils ship banded with edge protectors, wrapped in VCI film for sea freight.

galvanized steel coils banded with edge protectors

Enquiries

Send the thickness, width, spangle, coil weight and mandrel diameter, plus what the coil gets made into. If you are not settled on coating weight, tell us where the product ends up and we will recommend Z60, Z120 or Z275 with the reasoning written on the quotation. Reply and sample certificate within 12 hours.

Send Inquiry

(0/10)

clearall