A36 H Beams
A36 H Beams
video
A36 H Beams
A36 H Beams1
A36 H Beams3
A36 H Beams4
1/2
<< /span>
>

A36 H Beams

A36 H Beams in a full range of sizes and grades, with stock lengths, cut-to-length service, third party inspection and mill test certificates on request. Send your size list and destination port for a quote within 12 hours.

Watch an erector splice a column at height and the section shows its hand immediately. The bolt holes line up across the splice plate without a podger bar being hammered through, the web stays plumb while the group talks about the next lift, and the beam sits down on the seat without the crane having to hold it. A36 H beams earn that reputation on site, and it is worth more to the erection crew than the section modulus figure printed on the drawing.

A36 H beams loaded for shipment

Hot rolled or welded - which the job needs

Both routes are used and they are not interchangeable in every case. Hot rolled sections come off the mill with a continuous grain flow through the fillets and no weld in the web, which suits fatigue-sensitive work and anything exposed. Welded sections are made from plate, so they can be produced in combinations the mill does not roll, and they are often the answer when a project needs a deep section quickly. Tell us if the specification forbids one of the two, because it changes what we can offer.

The size envelope we hold

Sections run from 100 x 50 mm up to 1000 x 300 mm, with flange thickness between 6 mm and 18 mm and web thickness between 7 mm and 35 mm. That range covers portal frames, mezzanine floors and crane rails, but the limits are not all available in stock at once. For a project lifting several hundred tons, send the section list with the beam schedule and we will confirm availability by section rather than in general terms.

Grades and standards

Engineering grades are Q235, Q345, Q345B, A36 and S235JR, produced and documented against ASTM, GB, JIS or EN depending on the market the project is being built for. The differences matter at the connection design stage more than at the mill, so the grade decision should come out of the structural drawing, not out of what happens to be in the yard.

A36 H beam web and flange close-up

Surface treatment before loading

Beams can leave as-rolled, sand blasted, galvanized, painted, oiled or cut to length. Oiling is common when the steel will sit on a dock for weeks before erection; blasting is chosen when the paint specification has a surface grade attached to it; galvanizing goes on the sections that will stay exposed. Cutting to length before shipment saves the site a burning table but adds handling cost at our end, so it is worth comparing against site cutting for small projects.

Where the beams are used

Construction takes most of the tonnage - industrial buildings, workshops, warehouses and multi-storey frames. Bridge and road work uses them for approach spans and temporary crossings. Shipyards use them for keel blocks, cradles and dock fabrication. The surface finish usually follows the application rather than the other way round.

Questions from the fabricator

Can you supply cut to length with the web holes drilled? Yes, both. Send the drawing and we will quote it as a separate line so you can compare against doing the work on site.

What tolerance should we expect on the section? Standard mill tolerances apply, and the inspection report states what was measured. If your connection requires tighter than standard, raise it before the mill order is placed - it cannot be corrected afterwards.

Send the beam schedule with spans and tonnage, and we will come back with the section availability, the grade and the finish options.

Hot Tags: a36 h beams, a36 h beams price, a36 h beams supplier, buy a36 h beams, a36 h beams specification, h beams exporter, 100 50mm H Beams, Q235 H Beam Steel, H Beams Q345 For Building, High Strength H Beam For Building, H Beams, Wide Flange H Beams

Send Inquiry

(0/10)

clearall