
SPCC 0.2mm Cold Rolled Steel Sheet
SPCC 0.2mm Cold Rolled Steel Sheet in a full range of sizes and grades, with stock lengths, cut-to-length service, third party inspection and mill test certificates on request. Send your size list and destination port for a quote within 12 hours.
On a reversing mill the last pass is where a 0.2 mm sheet is won or lost. The reduction is small, the gap between the work rolls is measured in hundredths of a millimetre, and the tension between coiler and mill has to stay even, or the strip leaves with a wavy edge that later levelling cannot fully take out. Buyers ordering this gauge for appliance housings or steel drums tend to ask about rolling practice before they ask about price, because flatness at 0.2 mm is a result of the process rather than something that can be sorted out afterwards.

From pickled hot rolled coil to a 0.2 mm finish
Cold rolled sheet begins as hot rolled coil. The oxide layer is removed by pickling, the coil is rolled at room temperature through a tandem or reversing mill, and the strip is then annealed to restore the ductility that cold work removes. A final skin pass sets the surface and holds the shape. Because the whole sequence runs below the recrystallisation temperature, no mill scale forms and the thickness tolerance stays tight, which is what allows a press tool to be set once and then left alone.
Grades that behave at this thickness
The grades on this line are SPCC, SPCD and SPCE, together with ST12 and DC01 and the structural Q195, Q235, Q345 and Q275. SPCC is the general-purpose choice, SPCD and SPCE carry the better formability needed when a part involves a deep draw, and DC01 appears on drawings written to European practice. Thickness across the cold rolled range runs from 0.2 mm to 4 mm. At the thin end the grade and the annealing cycle decide whether the strip can be bent and stretched without cracking, and sheet length is cut to the customer's request.
What is checked rather than assumed
Thickness is measured at several points across the width instead of at one spot, because a 0.2 mm sheet can drift over a metre of width while the average reading still looks correct. Surfaces are inspected for roll marks, scratches and oxide, and flatness is checked on a plate bed. Packing follows weight: plates under one tonne are bundled with two to four steel strips, and heavier plates are handled piece by piece so the edges are not nicked during lifting.
Where this gauge gets used
Automotive covering parts, air conditioner panels and microwave housings rely on a surface clean enough to take paint or a zinc coating directly. Steel drums and packaging boxes use the ultra-thin end of the range, while curtain wall substrate and indoor partitions often take the same material after galvanising. In all of them the cold work hardening is useful, because it raises strength and hardness without changing the chemistry of the steel.

Loading, terms and specifying an order
For a 20 ft container we work within 2300 mm width and 6000 mm length; a 40 ft container takes the same width up to 12000 mm. Oversize or very heavy plates go by bulk vessel, where freight is lower and crane capacity is less of a constraint. Delivery normally runs 15 to 20 days from a 30% deposit, with the balance against documents; T/T and irrevocable L/C at sight are both accepted, and EXW, FOB, CFR and CIF quotes are available. Send the part drawing, the grade and the thickness tolerance you need, and the offer will state the annealing condition and the surface finish rather than leaving both to be discovered on arrival.
Hot Tags: spcc 0.2mm cold rolled steel sheet, spcc 0.2mm cold rolled steel sheet price, spcc 0.2mm cold rolled steel sheet supplier, buy spcc 0.2mm cold rolled steel sheet, spcc 0.2mm cold rolled steel sheet specification, cold rolled steel sheet exporter, DC01 Carbon Cold Rolled Steel Plate, Cold Rolled Mild Steel Sheet, Cold Rolled Alloy Metal Sheet, Cold Rolled Steel Sheet, SPCC 0 2mm Cold Rolled Steel Sheet, Cold Rolled Steel Plates 0 5mm
Send Inquiry










