Cold Rolled Alloy Metal Sheet
Cold Rolled Alloy Metal Sheet
video
Cold Rolled Alloy Metal Sheet
Cold Rolled Alloy Metal Sheet
Cold Rolled Alloy Metal Sheet
Cold Rolled Alloy Metal Sheet
1/2
<< /span>
>

Cold Rolled Alloy Metal Sheet

Cold Rolled Alloy Metal Sheet in a full range of sizes and grades, with stock lengths, cut-to-length service, third party inspection and mill test certificates on request. Send your size list and destination port for a quote within 12 hours.

The first thing a toolmaker asks about a thin cold rolled coil is not the grade. It is whether the thickness holds across the width, because a blank running 0.03 mm heavy on one side shifts the clearance in a compound die and the burr turns up on the part that matters. On this sheet the thickness sits inside a band of plus or minus 0.02 to 0.05 mm, the strip comes off straight, and the edge is cut clean and free of burrs.

Sheet of this kind runs between 0.2 mm and 0.5 mm thick. Below that the same route keeps going: cold rolling reaches below 0.1 mm, and the steel for food and beverage cans sits around 0.2 mm, a gauge no hot rolling line holds with the surface a decorated can needs.

cold rolled alloy metal sheet with smooth natural surface

Cold Rolled Alloy Metal Sheet product photo

Cold Rolled Alloy Metal Sheet steel sheet detail

Cold Rolled Alloy Metal Sheet plate surface

Cold Rolled Alloy Metal Sheet mill finish

What rolling, annealing and tempering leave on the surface

Working the steel below the recrystallisation temperature leaves no oxide scale and no rust on the surface, so nothing has to be pickled or ground off before the sheet goes to a spray line or a plating bath. The finish can be produced at high gloss, up to mirror quality, or as a deliberate matte texture where glare is a problem on the finished part. Loss at the trimming stage is smaller than on a wavy coil, because the strip arrives straight and the edges are tidy.

Cold Rolled Alloy Metal Sheet sheet edge

Cold Rolled Alloy Metal Sheet packed for shipment

Cold Rolled Alloy Metal Sheet loaded for delivery

Cold Rolled Alloy Metal Sheet sheet in use

The strength comes from the working, not the chemistry

The grades supplied are Q195, Q215, Q235 and Q275 alongside SPCC, SPCD and SPCE, ST12 and DC01, written to AISI, and all of them are low carbon. Strength is a product of the rolling: the grains are deformed and left in a worked state, which pushes tensile strength on an SPCC sheet into the 270 to 380 MPa range, well above the equivalent hot rolled material. Hardness rises with it, and the microstructure stays uniform from the head of the coil to the tail.

Formability is measured on a different number. The r-value here is above 1.5, and that is the figure that matters for a deep drawn part, because it describes how the material thins in different directions as it stretches. A grade that presses well one way and splits the other will not be rescued by its tensile figure.

cold rolled steel sheet surface and edge finish

Cold Rolled Alloy Metal Sheet product photo

Cold Rolled Alloy Metal Sheet steel sheet detail

Cold Rolled Alloy Metal Sheet plate surface

Where it goes, and one point to raise early

Automobile parts, home appliances, building materials and general machinery take it, and the reason is the same each time: a thin gauge, a tight tolerance and a surface that accepts a coating without preparation. The standard product is mid hard, the surface is supplied in its natural condition, and the coil is slightly oiled to keep it that way in transit. Delivery is normally 15 to 21 days.

Pressing an appliance bracket and drawing a can body are both done on this material, and they are not the same job. One bends along a single line; the other stretches the sheet in two directions at once. The grade and the annealing condition are what separate them, so where a part involves a deep draw rather than a simple bend it is worth saying so when the coil is ordered, before the material is cut.

Cold Rolled Alloy Metal Sheet mill finish

Hot Tags: cold rolled alloy metal sheet, cold rolled alloy metal sheet price, cold rolled alloy metal sheet supplier, buy cold rolled alloy metal sheet, cold rolled alloy metal sheet specification, cold rolled steel sheet exporter, Cold Rolled Mild Steel Sheet, DC01 Carbon Cold Rolled Steel Plate, Steel Sheet, SPCC 0 2mm Cold Rolled Steel Sheet, Cold Rolled Steel Sheet, Mild Steel Cold Rolled Sheet

Send Inquiry

(0/10)

clearall