A786 Checkered Plate (Hot Rolled Floor Plate, 3/16 In, 4x8 Ft)

A786 Checkered Plate (Hot Rolled Floor Plate, 3/16 In, 4x8 Ft)

ASTM A786 / A786M hot rolled floor plate in A36 and SS400 base, 3/16 in (6 mm base) to 1/4 in, 4x8 ft and 1500x3000 mm sheets, teardrop or lentil pattern, base thickness measured and stated separately from pattern height, mill edge or sheared, 3.1 MTC per heat.

Arguments about checkered plate are almost never about the pattern. They are about thickness, and the argument usually starts in a workshop three weeks after the container lands, when somebody puts a caliper on a plate and reads 5.4 mm on a 3/16 inch order. The plate is not wrong. He measured between the lugs, on the flat, which is the correct place to measure, and 3/16 inch is 4.76 mm of base plate plus the pattern rolled on top. If the supplier quoted the overall height, the deck he builds will be a little softer than the drawing says.

We roll this on our own hot strip mill and raise the pattern in the last stand, so there is no third party in the chain when you ask which heat the plate came from. Base thickness and pattern height go on our offer as two separate numbers. Buyers who have been burned once tend to appreciate that.

A trailer builder in Mombasa found out the hard way. He ordered 40 sheets of 3/16 for tipper decks, got plates that measured 4.3 mm on the flat, welded them down anyway because the trucks were sold, and had two decks dimple inside a month under 20 t loads. He now asks every supplier for the base thickness in writing before the proforma. That is a fair request and it costs us nothing to answer.

Specifications

ItemRange
StandardASTM A786 / A786M, EN 10025-2 base grade on request
Base gradeA36, SS400, S275JR, Q235B
Base thickness2.0 / 3.0 / 4.0 / 4.5 / 6.0 / 8.0 mm (3/16 in = 4.76 mm)
Pattern height1.0 – 1.8 mm above base, stated on the MTC
Sheet size1219 x 2438 mm (4x8 ft), 1500 x 3000 mm, 1500 x 6000 mm
PatternTeardrop (atlas), lentil, diamond; one side, reverse plain
Thickness tolerance±0.3 mm on base for 3 – 6 mm, ±0.4 mm above
Flatness8 mm per metre maximum, 12 mm on 6 mm and heavier
EdgesMill edge, sheared, or flame cut to size
SurfaceMill finish, pickled and oiled on request
TestingTensile and yield per heat, bend test, dimensional check per lot
DocumentsEN 10204 3.1 MTC, packing list with net and gross weight

Where the caliper goes

Put the jaw on the plain land between two lugs, not on top of a lug, and not on the edge where the shear has pulled a burr. Two readings a metre apart, then one at the centre. If the three agree within 0.2 mm you have a plate with a consistent base. If the centre reads 0.4 mm under the edges, the plate was rolled wide and the crown is in the middle, and no amount of pattern is going to hide it. We check three sheets per bundle this way before strapping, and the numbers go on the inspection sheet that travels with the lot.

teardrop pattern close up on hot rolled checkered plate

Pattern choice is a fabrication decision, not a cosmetic one

Teardrop is the default for trailer decks and platform floors because the lugs point one way and water runs off. Lentil is more common on stair treads and walkways where people come at the plate from any direction, since the pattern is symmetrical and the grip does not depend on which way you walk. Diamond reads sharper and some buyers ask for it by name, usually for export crates and container flooring.

One thing worth saying out loud: when you join two sheets, run the pattern the same way. Sounds obvious. A fabricator in Johor sent back photos of a stair landing where the two plates met at 90 degrees, pattern fighting pattern, and the seam collected water and rusted a brown line down the stringer within a season. He flipped one sheet on the next order and the complaint disappeared.

two A786 checkered plates stacked showing pattern direction

Cutting, welding, galvanizing

A786 base is plain carbon steel, so it welds with ER70S-6 and a normal MIG set, and it cuts with plasma or a guillotine without drama. Two practical notes from the shop floor. First, shearing 6 mm checkered leaves a slight wave along the cut edge because the pattern interrupts the blade, so if the edge is visible, flame cut or order it sheared 5 mm oversize and trim after. Second, if the plate is going for hot dip galvanizing, tell the galvanizer it is checkered. The lugs hold a thicker zinc layer than the flat and the piece can bow when it comes out of the kettle if it is a large thin sheet.

single A786 floor plate sheet with teardrop pattern

Loading, and why 4x8 is not always the cheap option

A 6 mm base 4x8 sheet weighs around 145 kg. Twenty-five tonnes is roughly 170 sheets, which is a full 20 ft with the plates standing on edge in a cradle. Cut-to-length 1500 x 3000 saves cutting waste on large decks but loads fewer square metres per container, so on a price per square metre basis the 4x8 usually wins. Send me the finished part size and I will work out which sheet size gives you the least offcut, rather than letting you pay for steel that ends up in the scrap bin.

Request a Quote

Tell me the base thickness, the sheet size, the pattern and the base grade, and whether the plate will be welded, galvanized or just cut. If your drawing says 3/16 or 1/4 inch, say it that way and I will confirm the millimetre base we will roll, so nobody is measuring lugs on arrival. A sales engineer replies within 12 hours with price, weight per sheet and the loading plan.

Send Inquiry

(0/10)

clearall